Share:


Obaproof WP-500 FIBER



Obaproof WP-500 FIBER

Water-Based Liquid Elastic Waterproofing Coating with Internally Reinforced Micro-Fibers

Obaproof WP-500 FIBER is a one-component, styrene-acrylic copolymer liquid waterproofing membrane reinforced with internal micro-fibers. It cures to foam a tough, flexible, and durable protective membrane layer suitable for harsh and tropical climates.

Packing: 1kg / 5kg / 20kg
Form: Emulsion
Appearance: White / Grey

Product Overview
A specialized water-based liquid elastic coating engineered with built-in micro-fiber reinforcement to significantly enhance tensile strength and resist tearing. It easily accommodates structural expansion and shrinkage movements without cracking, providing an impervious, weather-resistant barrier for exposed horizontal roofs and vertical wall surfaces.

Key Advantages
  • Internally Reinforced Strength: Integrated micro-fibers substantially increase tensile strength (~2.2 N/mm2) while maintaining elastic elongation (~155%).
  • Weather & UV Resistant: Highly resistant to prolonged UV rays, torrential rain, and water splashes without degrading.
  • Seamless Crack Bridging: Penetrates into hairline cracks and absorbs expansion movements to eliminate water ingress.
  • Eco-Friendly & Safe: Water-based, low VOC formulation, non-toxic, odorless, and non-flammable.

Recommended Applications
  • Exposed horizontal and sloped roofs (concrete decks, asbestos roofs, clay/concrete roof tiles, and cement mortar) 
  • Metal and zinc roofs or eaves
  • External vertical walls (brickwork with plaster, mortars, and parapets) against surface water penetration
  • Waterproofing underlayment beneath tiles (e.g, balconies)

Coverage Rates
  • Primer Coat: 0.2kg/m2 (Obaproof CM-700 diluted 1:3 with clean water)
  • First Coat: 0.75kg/m2 of Obaproof WP-500 FIBER
  • Second Coat: 0.75kg/m2 of Obaproof WP-500 FIBER
Obaproof WP-500 FIBER must be applied in a minimum of 2 coats (excluding the primer layer) to achieve complete waterproofing performance.

Application & Working Guidelines
  • Surface Preparation: Substrates must be clean, dry, structurally sound, and cleared of dust, grease, oil, and loose material.
  • Priming: Dilute 1 part Obaproof CM-700WP with 3 parts clean water and apply a thin priming coat at 0.2kg/m2. Allow to dry for approximate 30 minutes.
  • Mixing: Stir manually or blend with a low-speed mechanical mixer until the emulsion is completely homogeneous prior to use.
  • Application & Recoating: Apply evenly using a brush or roller. The film becomes tack-free within 1 to 2 hours (at +30°C). Allow the first coat to dry thoroughly before applying the second coat crosswise.
  • Curing: Full cure is reached in approximately 60 hours (at +30°C). Apply as an exposed finishing coat or protected layer with adequate drainage.
  • Clean-up: Clean all brushes, rollers, and application tools with clean water immediately after use. Cured material must be removed mechanically.

Important Limitations
  • Not for Immersion: DO NOT use in areas subject to permanent water contact, ponding, or water immersion (such as swimming pools, water tanks, shower enclosures, toilets, or wet kitchens).
  • Surface Care: Avoid dragging or placing sharp , piercing objects directly on top of the cured membrane.

Storage & Safety
  • Shelf Life: Up to 12 months from manufacture date in original, unopened, and undamaged sealed packaging stored between +5°C and +30°C.
  • Safety Precautions: Wear protective gloves, protective dust masks, and safety eyewear during handling. Keep out of reach of children.


 Inquiry - Obaproof WP-500 FIBER