Share:


MAPEI Novoplan 200 MY



MAPEI Novoplan 200 MY Self-Leveling Compound

Fast-Setting Self-Levelling Smotthing Compound

MAPEI Novoplan 200 MY is a fast-setting, hydrating cementitious self-levelling compound composed of special cements, graded silica sand, resins, and performance additives. When mixed with water, it creates a smooth, free-flowing slurry engineered to level and smooth interior subfloors prior to floor covering installation.

Packing: 25kg
Form: Powder
Color: Grey

Product Overview
A high-flow, rapid-hardening smoothing compound developed for interior flooring applications requiring a flat, even, and durable substrate. Formulated for single-coat thicknesses from 1 mm up to 5 mm, it bonds strongly to properly primed concrete, screeds, and existing tiled floors, allowing fast project turnarounds before laying vinyl, carpets, timber, or ceramic tiles.

Key Advantages
  • Superior Flow & Workability: Self-levelling rheology spreads effortlessly to create an ultra-flat, smooth floor surface with minimal trowel work.
  • Versatile Thickness Range: Can be applied smoothly in layers from 1 mm up to 5 mm per coat without cracking or shrinking.
  • High Compressive & Flexural Strength: Cures into a dense, hard-wearing base capable of withstanding heavy foot traffic and commercial loads.
  • Multi-Substrate Compatibility: Suitable for leveling new or existing concrete slabs, cement screeds, and properly prepared ceramic or terrazzo tiles.

Recommended Applications
  • Smoothing and leveling uneven concrete slabs and cementitious screeds in residential and commercial interiors
  • Preparing flat subfloors prior to installing vinyl planks, carpets, linoleum, rubber, and engineered wood flooring
  • Skimming and leveling over existing ceramic, porcelain, or terrazzo tiles
  • Interior renovation projects requiring rapid installation schedules

Coverage & Mixing Proportions
  • Mixing Ratio: 6.0 to 6.5 litres of clean water per 25kg
  • Application Thickness: 1mm to 5mm per coat
  • Consumption: Approximately 1.6kg/m2 per mm of thickness

Application & Working Guidelines
  • Surface Preparation:  Substrates must be solid, clean, dry, and cleared of dust, moss, oil, grease, and loose coatings. 
  • Priming: Prime with Mapei Primer G (diluted 1:1 to 1:3 with water depending on porosity) and allow to dry completely (~2 hours) to prevent pinholes and rapid moisture loss.
  • Mixing: Pour 6.0 to 6.5 litres of clean water into a clean mixing pail, then slowly add one 25 kg bag of Novoplan 200 MY while stirring continuously with a low-speed electric mixer until a completely smooth, lump-free, self-levelling liquid is obtained.
  • Application: Pour the mixture onto the primed floor within 30 minutes. Spread evenly using a smooth flat trowel, then immediately roll over the wet surface with a spiked roller to release trapped air bubbles and achieve a uniform level finish.
  • Curing: Ready for light foot traffic after approximately 4 hours. 
  • Working Temperature: Apply within an ambient and substrate temperature range of +5°C to +35°C.
  • Clean-up: Tools and equipment can be cleaned with clean water immediately after use. Cured material must be removed mechanically. 

Storage & Safety
  • Shelf Life: 12 months from manufacture date in original, unopened, and undamaged sealed pails.
  • Storage Conditions: Store in a ventilated, shaded, and dry environment.
  • Safety Precautions: Contains Portland cement which reacts alkaline with water and may cause skin or eye irritation. Wear protective rubber gloves, dust masks, and safety goggles during mixing and application. In case of eye contact, rinse immediately with generous amounts of clean running water and seek medical attention if irritation persists. Keep out of reach of children.


 Inquiry - MAPEI Novoplan 200 MY