Obaproof TO-1000 (Mineral Type)
Torch-Applied Bituminous Waterproofing Membrane (UV-Exposed & Trafficable)
Obaproof TO-1000 (Mineral Type) is a high-strength, pre-fabricated APP/polymer-modified bituminous waterproofing sheet reinforced with non-woven polyester and finished with protective natural mineral slate granules. Installed via propane gas torching, it creates an exposed, UV-stable, and trafficable waterproofing barrier suitable for both new RC structures and roof re-waterproofing works.Packing: 1m x 10m Roll (10m2 per roll)
Thickness / Weight: 3.0mm (Approx.40kg/roll) ; 3.5mm (Approx.45kg/roll); 4.0mm (Approx.50kg/roll)
Appearance: Natural Mineral Granule Finishing
Product Overview
A heavy-duty, factory-manufactured torch-on sheet membrane engineered for direct atmospheric exposure without the need for a protective cement screed. Reinforced with a tough non-woven polyester core, it provides superior dimensional stability, crack-bridging capability (> 2 mm), and high tensile strength (> 5.4 MPa). Its embedded mineral granule surface shields the underlying bitumen from UV degradation, solar heat, and maintenance foot traffic.
Key Advantages
- UV-Exposed & Trafficable: Protective mineral granule top layer resists harsh sunlight, UV aging, and foot traffic without requiring an additional protective screed.
- High Tensile & Puncture Resistance: Reinforced polyester core delivers high tear strength (> 5.4 MPa), 63% elongation at break, and strong resistance to mechanical puncture.
- Superior Crack Bridging & Thermal Stability: Bridges structural cracks exceeding 2 mm and maintains dimensional stability across extreme temperature fluctuations.
- Ideal for Re-Waterproofing & Maintenance: Precision-manufactured 3mm to 4mm sheet ensures uniform protection over both new concrete decks and existing roof renovations.
- Complete Water & Vapour Barrier: Forms an impermeable, fully fused monolithic shield when overlaps are heat-welded.
Recommended Applications
- Exposed reinforced concrete (RC) flat roofs, pitched roofs, and car porch roofs
- Balconies, terraces, walkways, and podium decks
- Roof re-waterproofing and maintenance refurbishment projects
- RC gutters, parapet walls, and planter boxes (with root-resistant protection)
- Concealed waterproofing systems for kitchens, bathrooms, driveways, foundations, and basements
Coverage & Installation Dimensions
- Roll Coverage: 10m2 per roll (1m x 10m), yeilding approximately 8.5m2 to 9.0m2 net coverage after accounting for side / end overlaps and vertical upturns
- Bitumen Primer Consumption: ~0.25kg/m2
- Side & End Overlaps: Minimum 75mm (100mm recommended at end laps)
- Vertical Upturn / Skirting Height: Minimum 300mm above finished floor level
Application & Working Guidelines
- Surface Preparation: Substrates must be structurally sound, clean, dry, and free of dust, cement laitance, oil, grease, and sharp protrusions. Remove any old, debonded waterproofing membranes or coatings during repair works. Repair honeycombing, cracks, and ponding depressions using structural patching mortar or cement/epoxy grout.
- Priming: Apply a thin, uniform coat of compatible bitumen primer at ~0.25 kg/m² using a roller or brush. Allow approximately 4 hours for the primer to cure tack-free (depending on ambient weather conditions).
- Membrane Alignment & Torching: Unroll Obaproof TO-1000 and align carefully, starting from the lowest gradient point (gutters and scupper drains), moving across the main floor slab toward the high point, and finishing with vertical wall skirtings. Using a propane torch gun, evenly heat the underside of the membrane and the primed substrate until the bitumen melts into a glossy bead, pressing the roll firmly onto the floor to expel trapped air.
- Seam Welding: Pay strict attention to the 75mm overlap joints—heat both the lower sheet and upper overlap thoroughly and press down with a heated trowel until a continuous bead of molten bitumen extrudes along the seam edge.
- Testing: Restrict all foot traffic during curing. Conduct a 24 to 48 hours water ponding test (subject to consultant approval) and inspect the underside slab soffit for any dampness or leaks before laying the protective cement screed.
- Clean-up: Clean bitumen primer from rollers and tools using suitable paint thinner or clean water (for water-based primers) immediately after use.
Storage & Safety
- Shelf Life: 12 months from manufacture date when stored upright in original, unopened packaging.
- Storage Condition: Store rolls vertically on pallets in a cool, dry, shaded, and covered area away from direct sunlight and open flames. Do not double-stack pallets.
- Safety Precautions: Torch application involves open flames and high temperatures—wear heat-resistant gloves, protective clothing, safety boots, and eye protection. Cover nearby combustible materials with non-flammable fire blankets, keep fire extinguishers on site, and exercise extreme caution during windy conditions. Prevent bitumen primer from contacting skin or eyes. Keep out of reach of children.
Inquiry - Obaproof TO-1000 (Mineral Type)